This cookie is set by GDPR Cookie Consent plugin. The cookie is used to store the user consent for the cookies in the category 'Other. The cookies is used to store the user consent for the cookies in the category 'Necessary'. The cookie is set by GDPR cookie consent to record the user consent for the cookies in the category 'Functional'. The cookie is used to store the user consent for the cookies in the category 'Analytics'. These cookies ensure basic functionalities and security features of the website, anonymously. Necessary cookies are absolutely essential for the website to function properly. Clamping steel directly to copper will result in galvanic corrosion and an eventual leak. The practical, less expensive and just as functional approach is to use steel L-brackets and place some durable plastic or rubber material between them and the copper pipe to prevent corrosion. What to put between copper pipe and wall? Use a stainless steel hose clamp (sometimes called a worm clamp becasue of the screw it uses) and a couple of L-brackets – clamp the L-brackets to the pipe using the hose clamp, screw them into the wall with wood screws. What kind of screw do you use to put pipe in wall? You can also use stand-off clamps intended for wall mounting on the vertical portion of the pipe. Is there a better way to do it? Help – front door opens onto stairs?Ĭlamping steel directly to copper will result in galvanic corrosion and an eventual leak. The floors are open now so lots of room to work and add whatever tees I need inbetween the floor joists, even if the pipe is held against the bottom of joist. Is there a better way to hang copper pipe to floor joists? Make sure you allow enough time for the tape to fuse to itself as well. Make sure the silicone tape overlaps itself (that’s how it sticks). Silicone tape along the base of the SharkBite valve should keep it from rotating on the pipe. How do you stop copper pipes from spinning? It can be supported by preformed copper pipe hangers, copper wire hangers, copper strapping or holes through structural wood framing members. How often does copper pipe need to be supported?Ĭopper pipe should be supported at 4′ intervals on a straight run and within 1 foot of a major change in direction. You can safely drill joists for electrical and plumbing runs without weakening the joists, if you follow the rules. In the case of your 2×10 joists, the maximum diameter is 35⁄64 in.Ĭan you drill holes in floor joists for plumbing? Notches can’t be deeper than one-sixth of the joist depth.

The maximum allowable diameter of a hole in any solid-lumber joist is one-third of the joist’s depth. How big of a hole can you drill in a 2×8 floor joist? Or you could box the pipe run and shield it. Piping run concealed in finished spaces has to be installed through the joists and protected from physical damage. Use a stainless steel hose clamp (sometimes called a worm clamp becasue of the screw it uses) and a couple of L-brackets – clamp the L-brackets to the pipe using the hose clamp, screw them into the wall with wood screws.Ĭan you run gas pipe through floor joists?ġ Answer.

How do you secure copper pipe to a wall?ĥ Answers. If you’re close to an exterior wall, you could drill straight out the wall and feed the pipe in straight, though that usually works better when the house isn’t already finished. There’s no easy way to run rigid pipe perpendicularly through joists. They are easily found, even in hardware store.Ĭan you run copper pipe through floor joists? You’re best option would be copper clevis hangers, 3/8″ allthread, and 3/8 floor and ceiling plate. How do you secure copper pipes to floor joists? 6 What kind of screw do you use to put pipe in wall?.5 Is there a better way to hang copper pipe to floor joists?.4 How often does copper pipe need to be supported?.3 How big of a hole can you drill in a 2×8 floor joist?.2 How do you secure copper pipe to a wall?.1 How do you secure copper pipes to floor joists?.

Os secure pipes